Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

Park Tool Bottom Bracket Wrench (External Bearing)
$25.95
The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.
Park Tool Disc Brake Mount Facing Tool Upgrade Kit
$31.90
- Contains the parts needed to update an older DT-1 Disc Brake Mount Facing Tool to a newer DT-1.2 model (PK-6353) and an older DT-4 Disc Post Mount Facing Tool to a newer DT-4.2 model (PK-6354) - Allows discontinued models to work more effectively on a wider variety of forks using 15mm and 20mm thru axles and frames using 12mm thru axles
Park Tool Facing Pilot
$11.34 - $21.22
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their centering pilots demonstrate their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size pilot: - 49.8mm (for 1.5-inch standard): The 767 is used with the HTR-1 (HTR-1B) and 690XL facer to perform facing only. It fits head tubes with an inside diameter of 49.8mm (1.5" standard). - 43.8mm (for ZS44 and EC44): The 768 Pilot is used with the HTR-1 (HTR-1B), the 750 Centering Cone Adaptor and 690XL facer to perform facing only. It fits head tubes designed for low profile or, “zero-stack,” headsets. These head tubes have nominal inside diameters of 43.9mm. - 55.9mm (for internal 1.5-inch ZS): The 790 Pilot takes the place of the 789 Reamer when performing head tube facing only. The 790 is used with the HTR-1 Headtube Reamer, the 690-XXL Facing Cutter, and the 750.2 Centering Cone Adaptor. The tool allows facing head tubes with 55.95 – 55.90mm I.D. (“Internal” 1-1/2” ZS standard).
Park Tool Saw Guide Insert
$12.95
Insert for the SG-7.2 Saw Guide to cut either alloy or carbon handlebars for the WTB PadLoc grips.
Park Tool Crown Race Setting System — Oversized
$95.95
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
Park Tool P-Handled Hex Wrench (2mm)
$6.95
Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.
Park Tool Centering Cone Adaptor
$49.20
Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.
Park Tool Cassette Lockring Tool
$8.00
Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut
Park Tool 42mm Head Tube Reamer & Facer Set For Hiddenset Headsets
$535.38
The 761s Reaming and Facing Cutters are used to machine head tubes using integrated headsets with a 42 mm bearing and 45 degree angular contact used by the Campagnolo® Hiddenset standard. FSA® and other manufacturers also make headsets in this standard. Includes upper and lower cutters.
Park Tool Metric Wrench
$6.49 - $11.95
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip.
Park Tool Threadless-Fork Saw Guide for Carbon Composite Forks
$44.95
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless carbon forks. Specially designed to accommodate wider, carbon specific saw blades, the SG-8 ensures a perfect cut every time. Slide on the guide, clamp it down and the specially shaped hardened-steel cutting slot guides your saw blade. And, the SG-8 Saw Guide ensures a straight, clean cut on fork steerer tubes up to 1-1/4-inches.
Park Tool THH Sliding T-Handle Hex Wrench
$13.49 - $25.95
Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions
Park Tool MTC-10 Multi-Tool
$13.95
The MTC-10 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 3, 4, 5 and 8mm hex wrenches - T25 Torx compatible driver - Combo cross/straight tip screwdriver - Key ring holder - Weight: 60g (2.12 ounces)
Park Tool THT Sliding T-Handle Torx Compatible Wrench
$12.95 - $16.95
Professional quality T-Handle star-shaped wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions
Park Tool Bottom Bracket Bearing Tool Set
$42.95
The BBT-30.4 Bottom Bracket Bearing Tool Set is designed and built to install and remove the bearings used in BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 bottom bracket systems. The BBT-30.4 features a bushing set used in conjunction with a head cup press to quickly and precisely press the BB30 and PF30 bearings in the bottom bracket shell. The included BB30 bearing remover works from inside the shell to easily push out bearings.
Park Tool Frame Tap 10mm x 1mm
$12.95
Frame Taps will become a lifesaver at some time for virtually every mechanic. As with all Park Tool Taps, these are made of high carbon steel and are precision ground. Park Tool Frame Taps cut easily and fit conventional tap handles. The TAP-10 is a 10mm x 1mm thread, the same thread for the derailleur hanger.
Park Tool Right Hand Bottom Bracket Tap
$305.32 - $338.74
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
Park Tool Internal Cable Routing Kit
$65.95
Take the guesswork out of installing cables, wires and housing inside the frame. The IR-1.2 speeds the internal frame routing of electric wires, shift cable/housing, brake cable/housing and hydraulic tubing on carbon fiber, titanium, and aluminum frames. Kit includes four plastic-coated 250cm cables with attached magnets and unique fittings plus an external guide magnet to speed operation. Newly updated to include a dedicated E-tube Di2 cable connector that easily pulls through a 6mm frame hole. Opposite polarity magnets on cables seek and attach inside frame tubes, making it easy to route through frame entrances and exits. Works with any size frame including tandems. A true time and frustration saver!
Park Tool BBT-59.2 Bottom Bracket Tool
$25.95
Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Featuring updated tooth profiles to optimize the fit between the tool and high performance BB parts. Anodized and laser engraved for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16 notch 41mm OD cups - Fits Shimano BBR60 (Ultegra 11-speed 6800 series), Shimano MT-800
Park Tool Crown Race Setting System Extension
$33.95
The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.
Park Tool Shop Cone Wrench (28mm)
$8.95
Park Cone Wrenches are made of durable tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Park's special Y-heads put more material where it's needed for excellent durability and strength. The 28mm size fits newer Shimano 20mm through-axles, as found on XT, XTR and Saint hubs. Most applications require at least 2 cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park Tool Shop Cone Wrench (24mm)
$9.00
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 24mm wrench fits Shimano 15mm through-axle front hubs and many suspension-fork top caps. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
Park Tool Pump Rebuild Kit
$9.95 - $12.95
Park Tool is world-renowned for their bicycle industry tools, and their pumps are no exception. Keep yours up to speed and working smoothly with these rebuild kits. - 1096K: Contains one #1081 head as well as one #1075 plunger gasket for older PFP-2 and first generation PFP-4 floor pumps. Also compatible with second-generation PFP-4 floor pumps. - 1096X: Contains one #1096R head, one #1472 fitting, and one #1075 plunger gasket for second generation PFP-4 floor pumps. Also compatible with PFP-2 and first-generation PFP-4 floor pumps. - 1096Z: Contains one #1096R head, one #1472 fitting, and one #1087 plunger gasket for PFP-5 and PFP-7 floor pumps. Also compatible with PFP-3, PFP-6, and PFP-8 floor pumps.
Park Tool SK-4 Home Mechanic Starter Kit
$169.95
A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench
Park Tool Threadless Star Nut Setter With Guide
$42.95
Park's Threadless Star Nut Setter makes it quick and easy to install star-fangled nuts used with 1-inch and 1-1/8-inch threadless headset systems. Using a durable steel driver and built-in guide, the TNS-4 perfectly aligns the star-fangled nut and sets it to the proper depth every time. Plus, the unique design virtually eliminates pinched fingers!
Park Tool Shop Cone Wrench (23mm)
$9.00
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 23mm size fits Shimano 15mm through-axle hubs. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
Park Tool Bottom Bracket Tool (Octalink / Isis)
$18.00
Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.
Park Tool Shop Cone Wrench (26mm)
$8.95
Park's Shop Cone Wrenches are made of durable tool steel and are thin to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Park's special Y-heads put more material where it's needed for excellent durability and holding power. The 26mm size fits through-axle end caps and suspension fork crowns. Most applications require at least 2 cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park Tool Handlebar Holder
$20.00
The Handlebar Holder prevents the handlebars and front wheel from swinging to the side and banging into the frame when your bike is mounted in a repair stand. It fits handlebars up to 32mm and all frame tubes up to 50mm in diameter, so it works on almost any road or mountain bike and is sure to make every repair easier.
Park Tool Axle Vise
$15.95
Park's AV-1 Axle Vise makes repairing and overhauling hubs easier than ever. It prevents your axle from spinning while work is done on the hub and it has two different size receptacles so it will work with both front and rear axles.